Chính hãng
E180-Z8910SP JN5189HN/001Z Module Zigbee 500m
Thương hiệu
EBYTE
Mô tả
Nguồn: 1.9 - 3.6 VDC, giao tiếp: UART
Hết hàng
(Đặt mua để có hàng sớm)
0
Phản hồi
|
Số lượng mua
(Cái)
|
Đơn giá
(VND)
|
| 1+ | 205.000 |
Giao hàng toàn quốc
Thanh toán khi nhận hàng
Cam kết đổi/trả hàng
Thông số
25 Sản phẩm tương tự| Thuộc tính | Giá trị | Tìm kiếm |
|---|---|---|
|
Điện áp cấp |
3.3V |
|
|
Giao tiếp |
UART |
|
| RoHS |
|
|
| 25 Sản phẩm tương tự | ||
Mô tả sản phẩm
Thông số kỹ thuật:
- Model: E180-Z8910SP
- IC chính: JN5189HN/001Z
- Điện áp hoạt đông: 1.9 - 3.6 VDC
- Giao tiếp: UART
- Tần số: 2405~2480 GHz
- Công suất: 11dBm
- Khoảng cách truyền tối đa trong điều kiện lý tưởng: 500m
- Hỗ trợ ăng ten: PCB
- Kích thước: 11.5x22.7mm
| Pin No. | Pin Name | Pin direction | Application |
|---|---|---|---|
| 1 | NC | - | Reserved, directly suspended |
| 2 | GND | - | Ground wire, connected to the power reference ground |
| 3 | NC | - | Reserved, directly suspended |
| 4 | PIO1(WAKE) | Input | The WAKE pin is mainly used to wake up the dormant terminal. It is high when it is powered on. When the pin is pulled low externally, the dormant terminal device will be awakened. |
| 5 | PIO8(TX) | Output | Serial transmission port TX |
| 6 | PIO9(RX) | Input | Serial receiving port RX |
| 7 | NC | - | Reserved, directly suspended |
| 8 | NC | - | Reserved, directly suspended |
| 9 | PIO2(MODE) | Input | Working mode switching pin, when the pull-down time is greater than 500ms,working mode switching. |
| 10 | PIO3(BAUD_R) | Input | The UART_BAUD_RESET pin is used to reset the baud rate of the device. It defaults to a high level after power-on. In any mode, the module serial port parameters will be restored to the default 115200 if the pin is pulled down for more than 1000ms. |
| 11 | PIO6(ACK) | Output | The ACK pin is used to indicate the status of the last user data transmission.The pin is pulled low before the transmission is started, and the pin is pulled high after the transmission is successful. |
| 12 | PIO7(GPIO0) | Input/Output | GPIO input/output port 0 |
| 13 | VCC | - | Module power supply positive reference voltage, voltage range |
| 14 | GND | - | Ground wire, connected to the power reference ground |
| 15 | PIO10(GPIO1) | Input/Output | GPIO input/output port 1 |
| 16 | PIO4 | - | Reserved, directly suspended |
| 17 | PIO5 | - | (PIO5 pulled low, the module is in download mode; PIO5 pulled high, the module is in running mode) |
| 18 | PIO16(AUX) | Output | The AUX pin indicates the current working status of the device. When the pin is low, it indicates that the device is busy, and the high level indicates that the device is idle. |
| 19 | PIO11(GPIO2) | - | Reserved, directly suspended |
| 20 | NC | - | Reserved, directly suspended |
| 21 | PIO14(ADC1) | Input | ADC detection port 1 |
| 22 | PIO15(ADC2) | Input | ADC detection port 2 |
| 23 | NC | - | Reserved, directly suspended |
| 24 | NC | - | Reserved, directly suspended |
| 25 | SWCLK | - | Reserved, directly suspended |
| 26 | SWDIO | - | Reserved |
| 27 | PIO17(PWM3) | Output | PWM output port 3 |
| 28 | PIO18(PWM2) | Output | PWM output port 2 |
| 29 | PIO19(PWM1) | Output | PWM output port 1 |
| 30 | PIO21(LINK) | Output | The LINK pin indicates the current network status of the module, and the output high-level meter has been added to the network |
| 31 | PIO20(PWM0) | Output | PWM output port 0 |
| 32 | NC | - | Reserved, directly suspended |
| 33 | NC | - | Reserved, directly suspended |
| 34 | NC | - | Reserved, directly suspended |
| 35 | NC | - | Reserved, directly suspended |
| 36 | GND | Input/Output | Ground wire, connected to the power reference ground |
| 37 | RESET | Output | Reset pin |