/upload/medium/3100.jpg

Phone

(28)3896.8699-0972924961

Giỏ hàng 0

Giỏ hàng trống

Danh Mục
Sản phẩm mới
Plato-107 Kìm Cắt
Kìm cắt dây, chân linh kiện 0.1mm, gọn nhẹ, độ cứng cao
0 đ/Cái
6P-ZH1.5-Female-15cm
Dây bus 6-Pin 1 đầu Female, pitch 1.5mm, dài 15cm
6,000 đ/Cái
KCD3-BIAN Công Tắc
3 Chân DPST Công Tắc Rocker 15A/20A 250V/125VAC
10,000 đ/Cái
DS-228 Nút Nhấn Giữ
Nút Nhấn Giữ, 2 chân, 12mm, 3A/125VAC 1.5A/250VAC
4,000 đ/Cái
PBS-110 Nút Nhấn Nhả
Nút Nhấn Nhả, 7mm, 2 chân, 250VAC/1A,125VAC/3A
4,000 đ/Cái
SPST-3P Công Tắc
20A 12V, 16A 12V 3 Chân, Có Đèn Led
4,000 đ/Cái
0805 120uH Cuộn Cảm
0805 120uH Cuộn Cảm, 5%
2,000 đ/Gói(5pcs)
0805 10nH Cuộn Cảm
0805 10nH Cuộn Cảm, 5%
2,000 đ/Gói(5pcs)
Phản hồi mới
PICKIT-3 Microchip

PICKIT-3 Microchip

Chính hãng Microchip, PICkit 3 In-Circuit Debugger

Nhà sản xuất: Microchip

Hết hàng ROHS

Số lượng mua

0 Phản hồi 1556 lượt xem

Bảng giá

Số lượng
(Bộ)
Đơn giá(VND)
1
849,000
5
820,000

Chính hãng Microchip


PICkit 3 In-Circuit Debugger

Microchip’s PICkit 3 In-Circuit Debugger/Programmer uses in-circuit debugging logic incorporated into each chip with Flash memory to provide a low-cost hardware debugger and programmer. In-circuit debugging offers these benefits:

  • Low cost
  • Minimum of additional hardware needed for debug
  • Expensive sockets or adapters are not required

The PICkit 3 can now also reprogram any PIC microcontroller

with a simple push of a button:

Find out more about Programmer-To-Go function

http://thegioiic.com/upload/large/3101.jpg

Note: The PICkit 3 In-Circuit Debugger/Programmer is NOT a production programmer. It should be used for development purposes only.

The MPLAB PICkit 3 allows debugging and programming of PIC® and dsPIC® Flash microcontrollers at a most affordable price point using the powerful graphical user interface of the MPLAB Integrated Development Environment (IDE). The MPLAB PICkit 3 is connected to the design engineer's PC using a full speed USB interface and can be connected to the target via an Microchip debug (RJ-11) connector (compatible with MPLAB ICD 2, MPLAB ICD 3 and MPLAB REAL ICE). The connector uses two device I/O pins and the reset line to implement in-circuit debugging and In-Circuit Serial Programming™.

PICkit 3 Features

  • USB (Full speed 12 Mbits/s interface to host PC)
  • Real-time execution
  • MPLAB IDE compatible (free copy included)
  • Built-in over-voltage/short circuit monitor
  • Firmware upgradeable from PC/web download
  • Totally enclosed
  • Supports low voltage to 2.0 volts (2.0v to 6.0v range)
  • Diagnostic LEDs (power, busy, error)
  • Read/write program and data memory of microcontroller
  • Erase of program memory space with verification
  • Freeze-peripherals at breakpoint
  • Program up to 512K byte flash with the Programmer-to-Go

Header Information

Some 8-, 14- and 18-pin devices use small header boards with a special MCU for debugging. This special MCU has extra pins for PICkit 3 communication and therefore allows the use of all pins on the part for the application. The header board is not used or needed for programming. However, when debugging these devices the header must be used. See the "Header Specification" document below or see a list of current devices that use headers here.

Phản hồi(0)

Mã xác nhận*

4xjmfq  

Vui lòng Đăng Nhập hoặc Đăng ký để chia sẻ.
Đang tải...
Sản phẩm nổi bật
Thegioiic live support