/upload/medium/2149.jpg

Phone

(28)3896.8699-0972924961

Giỏ hàng 0

Giỏ hàng trống

Danh Mục
Sản phẩm mới
AD16-16SM-24V Đèn Còi Báo
Đèn báo đỏ có còi 24VDC, D=20 mm, 5W
0 đ/Cái
ANTI-ST-CT-V2 Áo Chống Tĩnh Điện
Áo chống tĩnh điện, chống bụi, có nhiều màu, kích cỡ
119,000 đ/Cái
Anti-ST-HAT Nón Chống Tĩnh Điện
Có nhiều màu sắc
29,000 đ/Cái
ANTI-ST-STRAP Dây Chống Tĩnh Điện Giày
Dây Chống Tĩnh Điện Giày
29,000 đ/Cái
4.3inch FPGA LCD
LCD 4.3inch dùng cho board FPGA
1,190,000 đ/Cái
XC6SLX16 SPARTAN6 Xilinx FPGA Board
1Gb DDR3, 128Mb Flash, VGA, microSD, Jtag, USB
3,399,000 đ/Cái
XC6SLX9 SPARTAN6 Xilinx FPGA Board
SDRAM 256Mb, 16M Flash, VGA, microSD, Jtag, USB
1,349,000 đ/Cái
AD-DA-8Bit Module Chuyển Đổi AD-DA
DA chip: AD9708 8bit, AD chip: AD9280 8bit
589,000 đ/Cái
Phản hồi mới
PICkit 3

PICkit 3

PICkit 3 In-Circuit Debugger

Nhà sản xuất: Microchip

Còn: 2 Cái ROHS

Số lượng mua

0 Phản hồi 2584 lượt xem

Bảng giá

Số lượng
(Cái)
Đơn giá(VND)
1
685,000
3
675,000
5
655,000

Sản xuất: Trung Quốc


PICkit 3 In-Circuit Debugger

Microchip’s PICkit 3 In-Circuit Debugger/Programmer uses in-circuit debugging logic incorporated into each chip with Flash memory to provide a low-cost hardware debugger and programmer. In-circuit debugging offers these benefits:

  • Low cost
  • Minimum of additional hardware needed for debug
  • Expensive sockets or adapters are not required

The PICkit 3 can now also reprogram any PIC microcontroller

with a simple push of a button:

Find out more about Programmer-To-Go function

Note: The PICkit 3 In-Circuit Debugger/Programmer is NOT a production programmer. It should be used for development purposes only.

The MPLAB PICkit 3 allows debugging and programming of PIC® and dsPIC® Flash microcontrollers at a most affordable price point using the powerful graphical user interface of the MPLAB Integrated Development Environment (IDE). The MPLAB PICkit 3 is connected to the design engineer's PC using a full speed USB interface and can be connected to the target via an Microchip debug (RJ-11) connector (compatible with MPLAB ICD 2, MPLAB ICD 3 and MPLAB REAL ICE). The connector uses two device I/O pins and the reset line to implement in-circuit debugging and In-Circuit Serial Programming™.

PICkit 3 Features

  • USB (Full speed 12 Mbits/s interface to host PC)
  • Real-time execution
  • MPLAB IDE compatible (free copy included)
  • Built-in over-voltage/short circuit monitor
  • Firmware upgradeable from PC/web download
  • Totally enclosed
  • Supports low voltage to 2.0 volts (2.0v to 6.0v range)
  • Diagnostic LEDs (power, busy, error)
  • Read/write program and data memory of microcontroller
  • Erase of program memory space with verification
  • Freeze-peripherals at breakpoint
  • Program up to 512K byte flash with the Programmer-to-Go

Header Information

Some 8-, 14- and 18-pin devices use small header boards with a special MCU for debugging. This special MCU has extra pins for PICkit 3 communication and therefore allows the use of all pins on the part for the application. The header board is not used or needed for programming. However, when debugging these devices the header must be used. See the "Header Specification" document below or see a list of current devices that use headers here.

Phản hồi(0)

Mã xác nhận*

3Owe7q  

Vui lòng Đăng Nhập hoặc Đăng ký để chia sẻ.
Đang tải...
Sản phẩm nổi bật
Thegioiic live support