/upload/medium/202.jpg

Phone

(28)3896.8699-0972924961

Giỏ hàng 0

Giỏ hàng trống

Danh Mục
Sản phẩm mới
2.4-SZYTF TFT LCD Shield Arduino
2.4-inch LCD Module cảm ứng điện trở dùng cho Arduino UNO R3
125,000 đ/Cái
T30-H3-P05 Bánh Răng Lỗ 6mm
30 răng, lỗ 6mm, bước răng 0.5, cao 10mm, M3 screw
23,000 đ/Cái
T30-H3-P05 Bánh Răng Lỗ 5mm
30 răng, lỗ 5mm, bước răng 0.5, cao 10mm, M3 screw
23,000 đ/Cái
FM-1.27-2X40-SMD
80(40x2) pin 1.27mm SMD Female connector
15,000 đ/Cái
RJ11-4P4C-FM
Modular Plug Network Cable Connector Clear 6Pins-Female
1,300 đ/Cái
Module WiFi ESP8266-V1 Relay 5V
Input 5V, 10A/250VAC 10A/30VDC
165,000 đ/Cái
Module WiFi ESP8266-V12 Relay
Relay 10A 220V, Input 7-30VDC
180,000 đ/Cái
AD16-22SM Đèn Còi Báo
Đèn còi 12V,24V,36V,110V,220v,380V AC/DC <=20mA 80dB
35,000 đ/Cái
Phản hồi mới
ACS712ELCTR-20A-T

ACS712ELCTR-20A-T

20A 5V Hall Effect-Based Linear Current Sensor, Bidirectional

Nhà sản xuất: Allegro MicroSystems

Còn: 4 Cái ROHS

Số lượng mua

0 Phản hồi 2899 lượt xem

Bảng giá

Số lượng
(Cái)
Đơn giá(VND)
1
70,000
10
68,000
20
65,000
50
60,000

±20A 5V, Hall Effect-Based Linear Current Sensor IC with 2.1 kVRMS Voltage Isolation and a Low-Resistance Current Conductor

Features

  • Low-noise analog signal path
  • Device bandwidth is set via the new FILTER pin
  • 5 µs output rise time in response to step input current
  • 80 kHz bandwidth
  • Total output error 1.5% at TA = 25°C
  • Small footprint, low-profile SOIC8 package
  • 1.2 mΩ internal conductor resistance
  • 2.1 kVRMS minimum isolation voltage from pins 1-4 to pins 5-8
  • 5.0 V, single supply operation
  • 185 mV/A output sensitivity
  • Output voltage proportional to AC or DC currents
  • Factory-trimmed for accuracy
  • Extremely stable output offset voltage
  • Nearly zero magnetic hysteresis
  • Ratiometric output from supply voltage

Applications:

Motor control, load detection and management, switched-mode power supplies, and overcurrent fault protection

Category Sensors, Transducers
Family Hall Effect / Magnetic
Current - Sensing ±20A
Accuracy ±1.5%
Sensitivity 96 ~ 104 mV/A
Current - Supply 10mA
Sensor Type Hall Effect
Voltage - Supply 4.5 V ~ 5.5 V
Output 2.5V
Frequency 80kHz
Response Time 5µs
Polarization Bidirectional
Operating Temperature -40°C ~ 85°C
Package / Case 8-SOIC (0.154", 3.90mm Width)
Packaging Tape & Reel (TR)
Standard Package 3,000

Description
The Allegro® ACS712 provides economical and precise solutions for AC or DC current sensing in industrial, commercial, and communications systems. The device package allows for easy implementation by the customer. The device is not intended for automotive applications. For the automotive grade version, see ACS714.

The device consists of a precise, low-offset, linear Hall sensor circuit with a copper conduction path located near the surface of the die. Applied current flowing through this copper conduction path generates a magnetic field which is sensed by the integrated Hall IC and converted into a proportional voltage. Device accuracy is optimized through the close proximity of the magnetic signal to the Hall transducer. A precise, proportional voltage is provided by the low-offset, chopper-stabilized BiCMOS Hall IC, which is programmed for accuracy after packaging.

The output of the device has a positive slope (>VIOUT(Q)) when an increasing current flows through the primary copper conduction path (from pins 1 and 2, to pins 3 and 4), which is the path used for current sensing. The internal resistance of this conductive path is 1.2 mΩ typical, providing low power loss. The thickness of the copper conductor allows survival of the device at up to 5× overcurrent conditions. The terminals of the conductive path are electrically isolated from the sensor IC leads (pins 5 through 8). This allows the ACS712 current sensor IC to be used in applications requiring electrical isolation without the use of opto-isolators or other costly isolation techniques.

The ACS712 is provided in a small, surface mount SOIC8 package. The leadframe is plated with 100% matte tin, which is compatible with standard lead (Pb) free printed circuit board assembly processes. Internally, the device is Pb-free, except for flip-chip high-temperature Pb-based solder balls, currently exempt from RoHS. The device is fully calibrated prior to shipment from the factory

Download datasheet

Phản hồi(0)

Mã xác nhận*

Yw4Tbd  

Vui lòng Đăng Nhập hoặc Đăng ký để chia sẻ.
Đang tải...
Sản phẩm nổi bật
Thegioiic live support