Phone

(28)3896.8699-0972924961

Sản phẩm mới
PH-5H-16L Kim Test Kiểm Tra Mạch
L=38MM, Ø=3MM, 50mΩ
0 đ/Cái
Dây Cáp RJ45 Đực To RJ45 Cái
Dài 30cm, dây cáp enthernet, đường kính dây 5mm
16,000 đ/Sợi
Arduino ProtoShield Mega2560
Board shield dành cho các dòng Mega2560
62,000 đ/Cái
IRLR7843-CN
MOSFET MOSFT 30V 161A 3.3mOhm 34nC Log Lvl
3,500 đ/Cái
Còn: 600 Cái
Bàn Phím 1x4 Nút Nhấn
Bàn phím 4 nút nhấn, size: 37x15mm
12,000 đ/Cái
Arduino Uno WiFi R3 ATmega328 ESP8266
Điện áp: 6-9VDC, ATmega328, 32Mb memory
252,000 đ/Cái
2WD A30 Khung Xe Nhôm 2 Động Cơ
Khung xe bao gồm 2 động cơ, bánh xe và các phụ kiện đi kèm
238,000 đ/Bộ
5MM-200MM Thanh Trục
Thanh trục thép dài 200mm, D=5mm
14,700 đ/Thanh
Còn: 20 Thanh
Phản hồi mới
4500mAh 3.7v rechargeable li-po battery

4500mAh 3.7v rechargeable li-po battery

Size: 5.5±0.5×67±0.5×100±0.5 MM with G3J PCB

Nhà sản xuất: Đang Cập Nhật

Hết hàng

Số lượng mua

0 Phản hồi 3100 lượt xem ROHS

Bảng giá

Số lượng
(Viên)
Đơn giá(VND)
1
195,000
20
190,000
50
185,000

High energy density,good capacity,light and thin,safe and reliable(with PCM) ,long circle life,

Li-polymer Battery Specification
Model 5567100
Nominal voltage 3.7V
Nominal capacity 4500mAh
Size Thickness × Width × Length (mm)
5.5±0.5×67±0.5×100±0.5 (with PCM)
Main characteristics High energy density,good capacity,light and thin,safe and reliable(with PCM) ,long circle life,no memory,environmental,stable performance,reasonable low price,capacity and size could be customerized.
Weight about 16g
Max charge current 1C
Charging method charge with constant current 1C to 4.2V,then charge with constant voltage 4.2V till charge current less than 0.01C
Max discharge current 1C
Discharge cut-off voltage 3.0 V, the over-discharge detection voltage of PCM
Operating environment Charging, 0°C ~ 45°C ; 65±20%RH 
Discharging, -20°C~60°C ; 65±20%RH
Storage environment -20°C~45°
65±20%RH
storage for a long time(>3 months) and the storage condition shall be:<35°C;65±20%RH;3.7~3.9V
CycleLife
(80% Prime Capacity) :
>500times   
Charging Attention Charging current and charging voltage should be less than specified in the Product Specification.
The charger shall be designed to comply with Specification.
It is dangerous that charging with higher current or voltage than Product Specification may cause damage to the cell electrical,mechanical safety performance.

Dimension Drawing

 

 

Item

Description

Dimension and specification

T

thickness

5.5mm(max)

W

width

67mm(max)

H

length

100mm(max)

L1

Cable length

customised

 

2 Environment Characteristics

  No.

content

Testing method

Requirements

1

Hot&Humidity test

Full charging, store it at 40±2°C with 90%~95RH% for 48 hours. Then put the battery at room temperature 20±2°C for 2 hours. Then discharge to 3.0V @0.2C.

Discharging  time≥36Min

No explosion,

No transform, No erosion

No fire, No leakage.

2

Vibration  Test

After Standard Charging,fixed the battery to vibration table,then subjected to vibration test for 30 minutes per axis of XYZ axes Frequency rate :1 oct/min Vibration frequency : 10Hz-30Hz Excursion(single amplitude): 0.38mm  Vibration frequency : 30Hz-55Hz Excursion(single amplitude): 0.19mm

No leaking,

No fire,

No explosion

Volage≥3.7V

3

Shock test

After Standard Charging,test condition:

Acceleration :100m/s2  Crash time per min: 40~80 times

Pulse lasting time : 16ms  Shock times : 1000±10times 

No leaking,

No fire,

No explosion

Volage≥3.7V

4

Drop Test

After standard charging , drop the battery from 100cm height onto a 18mm~20mm thick hardwood. Two sides of X,Y,Z directions each (total 6 times)

After the drop test, discharge the battery @0.2C to 3.0V.

Then charge it @1C to full capacity. Continue the test, within 3 times the battery should reach the target once.

No leaking,

No fire,

No explosion

Discharging≥51min

Phản hồi(0)

4BVZ4u  

Hãy Đăng Nhập hoặc Đăng ký để chia sẻ.
Đang tải...
Sản phẩm nổi bật
Thegioiic live support